Version 1.02 released on 14 feb 2018
Version 1.03 released on 18 feb 2018
Version 2.04 released on 5 mar 2018
At this moment version 2.04 is released.
see the website fsqc.eu/faq.html for changes in the versions
Automaticly new versions are notifying to you when you start FsQC.
Unzip the file in any folder of your choise,
Start FSX or FS2004 and load a flight and start FsQC, that's all.
********************************************************
Thanks to Paul Henty for the FSUIPC Client DLL for .net.
********************************************************
Requirements:
Computer with XP or higher and internet access.
flightsimulator FSX or 2004 installed.
FSUIPC installed and registered, you can download FSUIPC free from the internet on:
http://wwww.schiratti.com/dowson.html ".
If you run FsQC on a network computer (not the computer where FSX/FS2000 is running) you need to register WideFs in FSUIPC.
What this program do:
- quickly change the settings of FSX/Fs2004, such as time, date, fuel, weight, traffic etc.
- start a failure sytem, such as gear, flaps, engine, etc.
- freeze the time, so you can fly in a for everlasting sunset.
- runway detecting system to see wich runways are in use.
- a flight analysis system, this is automaticly started when you start FsQC.
- When flight analysis is finished you can print a report, the report is automaticly saved as pdf File.
- flight analysis is finished when you parked your aicraft with the parking brakes set for more then 5 seconds.
- graphical landingchart.
- load a existing flight or flightplan.
- quickly look to your CFG (settings) files (only FSX) and change them even before the flight simulator is running.
- After a flight is finished FsQC saves your flight automaticly as 'FsQC last Flight', so you can continue the next day or hour.
- for properly working, flight analysis require a fsx/fs2004 flightplan.
Flight analysis:
Flight analysis start recording at the moment when you begin taxiing.
It gives you huge information such as:
- takeoff- and landing-weight
- takeoff roll in m. or ft.
- separate fuel consumption in taxi, climb, cruise and descent.
- maximum banking in flight
- which speed you using the flaps and gear
- when autopilot on or off
- vertical speed on touchdown
- reverser set after landing
- wich speed you cancel reverser
- bouncing at landing
- graphical landingchart.
- and lots of more
You can better look the example of the pdf document located in the 'Flight Reports' folder.
Limited working:
FsQC is limited, you can only fly maximum 180 nm. from Greece Irakilon, LGIR, and maximum 180 Nm. from Greece Athene, LGAV.
When you are not in the limits, the program warns you with a messagebox and will be shut down.
So you can test the program fully before activate.
After activate there are no limits.
Free activation:
When you register with only your email address in the activation menu you will get 15 free startups or 30 days. without limitations. So you can test the program fully before activation. After activation there are no limits.
See in the activation menu.
Activated:
When activated, the program runs only on the computer where it was activated.
You can easily change this when you want it running on another computer.
You can change this for maximum 10 times.
So when you buy another computer there's no problem at all.
You can buy a license key at www.fsqc.eu
Reset activation:
When you run FsQC on another computer you get a message that it can only run on 1 computer, when that happens you must reset the activation, this is verry simple to do.
Go to the activate menu reset with your email and code, follow instructions given by the program, within 1 minut it's done.
Failures:
In the settings menu you can select the kind of failures you want to occur and when they must occur.
At this moment 10 failures are possible:
-altitude
-attitude
-heading
-airspeed
-vertical speed
-pitot
-fuelleak
-flaps
-engine
-gear
Recommended:
For more easy use, run this program on a second monitor or much better on a second computer(laptop) where FSUIPC-client is running in the same network where FSX/FS2000 is running and FSUIPC WideFs is registered.
See also the pdf Manual.
Also look at www.FsQC.eu for more information.
If you have a problem look first on www.fsqc.eu/faq.html
If you have questions please contact support@fsqc.eu
