Cessna 152 Photo-realistic Panel V1.1 Update for FS2000
Copyright Feb. 20002 by Chuck Grimes
******************************VERSION 1.1 CHANGES******************************************
Reduced all digital photo bitmap files in size to decrease the Over ALL size of the
Panel. Version 1.0 of this panel is no longer needed this update is a FULL VERSION.
gauges.zip gauge files required for panel - see installation instructions below.
Readme_First.txt This file
File_id.diz description file
Features.jpg jpeg image showing features of simulated panel
dfd300n3.zip Contains the 300S Radio Gauges, COMM 1 NAV 1, xxx NAV 2
dfd300x2.zip Contains the 300S Transponder Gauge
Panel.zip INCLUDES THE FOLLOWING
Panel.cfg Panel Configuration File
C-152.bmp Main panel bitmap
C-152_Landing.bmp Landing Panel bitmap
C-152-Forward_Left.bmp Forward left view
C-152_Forward_Right.bmp Forward right view
C-152_Right.bmp Right view
C-152_Left.bmp Left view
C-152_Rear_Right.bmp Rear right view
C-152_Rear_Left.bmp Rear left view
C-152_Rear.bmp Rear view
C-152_Xpndr.bmp Transponder Backpanel bitmap
C-152_YOKE.bmp Aircraft Steering Wheel
C-152_RPM_ZOOM.bmp RPM Gauge Backpanel bitmap
Panel Issues
(1)
Be sure to read the instructions in the dfd300ns.zip and dfd300x2.zip files when
installing the Radios and Transponder gauges especially the part that tells you
which folders to copy the FSSOUND.DLL and 300_switch.wav files into. There are
some SOUND CARD CHIP SITE'S THAT are not compatible with Dai Griffiths 300A Series
Radios which he gives a little detail in the Radio readme.txt.
(2)When you linger the mouse cursor over any gauge on the LANDING PANEL (except)
the Airspeed indicator NO instrument name appears.
(3)You can't adjust the VOR1 OBS on the LANDING PANEL with the mouse ,you have to
use the Keyboard.
Installation Instructions:
(1) Using Winzip V7.0 or higher, unzip the contents in the gauges.zip file into the
Main FS..\GAUGES FOLDER, (OVERWRITE) the "CESSNA_182_RG.FUEL.GAU" when Prompted.
(2) Unzip the the contents of the file dfd300n3.zip as follows.
dfd_nc385b.gau...into the Main \FS2k\GAUGES FOLDER.
dfd_nc385b2.gau..into the Main \FS2K\GAUGES FOLDER.
300_SWITCH.WAV...into the \FS2K\SOUND FOLDER.
FSSOUND.DLL......into the \FS2K\MODULE FOLDER. (VERY IMPORTANT MUST BE INSTALLED)
(3) Unzip the contents of the file dfd300x2.zip as follows.
dfd_300xpndr_b.gau...into the Main \FS2K\GAUGES FOLDER.
NOTE the remaining files are duplicates of the files install in step (2)
YOU DO NOT HAVE TO INSTALL THEM AGAIN.
(4) UNZIP the PANEL.ZIP Files into the Panel SUB-FOLDER of the aircraft you want
to use this Panel with and THAT'S IT.
System Requirements
The panel was tested on a PIII 1.0GB 382MB RAM, GeForce2 MX 64MB Graphics Card,
3D Mode, Resolutions of 1024 x 768 have been successfully tested.
PANEL CREDITS
In alphabetical order.
Arne B Bartels .....for Technical assistance.
Elmar Calbo........ for programming the Flaps_Lever gauge
Dai Griffiths...... for programming the 300S Radios.
Stephen Hayes...... for Project coordination,Flight Testing the Panel.
Nick Jacobs.........for promission to use his 300S Autopilot gauge.
Jean-pierre Langer..for promission to use his C-152 Airspeed gauge.
My apologies to anyone I may have missed.
===============================
DISCLAIMER
This panel is freeware, and as such, you must not make any money with any part of it!! No part of this panel (including bitmaps and gauge files) may be copied or reproduced in any way for inclusion in this or any other panel for which a fee is charged or money or any other benefit is received. Any user of this panel may, however, use it for the basis of starting a new FREEWARE panel design where similar artwork or gauges are required so long as the appropriate credits are given in an accompanying text file and no money is charged for any future releases.
These files should in no way harm anything on your computer. If you believe they have I accept no responsibility for any damages.The number of Aureal Chipsets is getting less as people upgrade.
!!!!!!!!! I HOPE YOU ENJOY MY PANEL !!!!!!!!!!!!!!
Any questions/comments Email charles.a.grimes@verizon.net
