*******************************************************************************
Boulton Paul P.100
by Kazunori Ito
*******************************************************************************
1.Description of this aircraft
2.Specification
3.About the installation
4.About the operations
5.About free software
6.About the directions point in FS2004 and FSX
*******************************************************************************
The Boulton Paul P100 was an unbuilt project for a ground-attack aircraft to a draft Air Ministry specification (unnumbered) of March 1942. The P100 was the most advanced and unorthodox of the many designs the aircraft industry responded with. It had a canard - pusher layout to give the pilot the best possible view and would have had an armament of 40mm and 20mm cannons along with bombs and rockets. The performance specified by the Air Ministry was not that very high, only 280 mph was asked for, stressing the over-riding need was for the accuracy of delivery of its weapons. To protect the pilot from being shreaded by the pusher prop in the event of having to bale out a sprung arm acted as a crude ejection system to swing him clear, although it ejected him downwards! - Not a direction to be flung in when flying a low altitude hedge-hopping ground attack aircraft! One would have to hope any stricken P100 would have had time to gain a bit of height before the pilot exited.
--------------------------------------------------
2. [ Specification ]
Length 10.2m
Spans 12.2m
Height 3.15m
Armer 40mm Canon x 4 / Missile x 8/ Other Bomb
Crew 1
Other unknown
-------------------------------------------------
3. [ About the installation ]
The airframe must copy the \BP P100 folder as it is in the Aircraft folder of FS2002 or FS2004.
\FS2002(FS2004)
-----\Aircraft
---------\BP P100
Please copy all files in the \gauges folder onto the gauge in the Gauges folder of FS2002 or FS2004.
A general gauge is saved for the gauge bundled this time.
The gauges of Kingair and GPS are not bundled.
Please setup it by yourself.
-----------------------------------------------------------
4. [ About the operations ]
Shift+"E" = Canopy Open
A special key operation is not used for this model.
-----------------------------------------------------------
5. [ About free software ]
All aircraft that I made are free software.
The reprint and the repaint may go freely.
However, please defend the following conditions.
1.The change in contents of this file is prohibited.
(Please distribute it like the Zip file of the current state when distributing it. )
2.Please neither reverse-assembly nor never remodel(convert) it of the aircraft model.
and don't covert my airframe for CFS Series.
3.Please don't bundle my airframe(MDL file) in the package of your works when you open the repaint to the public.
(Please open only the texture to the public. )
4.Don't use DXT format for making texture.
Please make it by the format that everyone can change.
It is necessary to be able to read and change with usual drawing software.
5.It is prohibited to bundle and to open a new panel to the public to my aircraft model.
(Please open only the panel to the public.
It is included in this file, and remodeling the panel that uses the panel background and the change in the panel background are prohibited. )
6.I maintain the copyright of the aircraft model and the panel background.
7.The copyright of the gauge belongs to the author.
---------------------------------------------------------
6. [ About the directions point in FS2004 and FSX]
This aircraft model is made by using FSDS Ver2.24.
Therefore, it is possible to play basically in FS2004(FS9) and FSX(FS10).
However........!!
In FS2004.
For a wide large-scale aircraft, the distortion is caused and the phenomenon of the aerofoil tip's disappearing happens in the spot shooting mode.
If this phenomenon happens, Please switch to the spot shooting mode by using other small aircraft.
Afterwards, if this aircraft is selected, it is normally displayed.
And........
In FSX.
Because gauges do not correspond to FSX, the gauges in the cockpit are not displayed.
Please you looks for a suitable gauges and setup Panel.cfg by yourself.
Sorry...............
*******************************************************************
Please Notice
I like military aircrafts. Especially, fighter!!
But, It is because the shape is unique and the manoeuverability is good.
I like aircraft that can freely fly in the big sky.
However............I hate war and combatting.
When I thinks the airframe that I made launches the bullet and the missile, I become scary.
Therefore, I'm prohibiting convert of my airframe for CFS.
If it is possible, I am wishing my airframe not to be used in CFS.
Though you might be said "Because it's simulation world"..........
Please..........Please.......
*******************************************************************
Please give mail to the following mail address when there is a recommendation of making the opinion and the thing that doesn't come.
KazuIto0926@aol.com
2012/03/12
Fukuoka, Japan
*******************************************************************